saladquiet1

Tips For Replacing a Window Handle Switching the handle on your window is a simple task that can be completed from the at-home comforts of your home. Follow these tips for an easy operation and a beautiful appearance. Start by removing the screw covers to expose the screws within your uPVC window handle. Measure the spindle to make sure you are getting the correct size replacement. 1. Measure the Spindle length If you're replacing a window handle it's important to get the size of the spindle correct. It can affect the tightness or elasticity of the handle as well as whether the handle will lock correctly into the frame of the window. The spindle is a metal shaft that connects to the handle and the lock in the window frame. The spindle is available in either the standard 8mm industry cross-section or older 9mm versions. Modern industry standards are 8mm, but it wasn't always that way. It is crucial to confirm the measurements before purchasing the handle you want to purchase. Take the handle off. This can be done easily by turning the handle into the open position, and taking off two screws that hold the handle in place (which are often hidden behind plastic caps which are required to be removed). After removing the handle, measure from the base of the handle to the end of the spindle. This will give you the measurement required to buy a replacement. There are plenty of choices when it comes to choosing the right window handle from sleek chrome that blends into a contemporary home to traditional brass that looks stunning in restored Georgian rooms, or the more quaint Tudor cottages with curved monkey tail latches! The possibilities are endless, but the most important thing is to choose a style that suits your home. Espag handles are typically used to uPVC window frames and are always the same size with a 43mm central. Cockspur handles are available in a range of sizes, from 58mm up to 62mm. Cadenza window handles are different in size as they have an angled blade which operates with a multi-point locking mechanism within the window. Another aspect to consider when selecting the best window handle is knowing which hand you will need to use, which is defined by what hand you use to open the door. Inline espag handles can be used for left or right-handed windows. Cranked window handles are only compatible for windows that open in a single direction. 2. Take the handle off A window handle that falls out is a frustrating experience, regardless of whether the handle is damaged or worn out. The good news is, you can fix a uPVC handle by yourself. All you require is a few basic tools and a bit of time to complete the job. You must first open the window and make sure it's not locked. Then, you need to remove the screws that hold the handle in place. Once these are removed, you can begin working on the removal of the handle itself. The handle is connected to a spindle inside the window frame. Based on the type, this is held in place with a screw or pin. The most common handles are the inline Espagnolette and cockspur handles. Both types of handles can be found on casement windows, including aluminum ones. You can lock the handles with a key in order to stop unauthorised access from outside. Or you can lock the handles by turning them clockwise. To take the handle off, you'll need a screwdriver with a flat blade to remove the clip that holds the handle. After this is released, the handle will slide off the spindle. When the handle is removed, you will have to determine the length of the spindle and ensure that your new handle is compatible with this size. Once you have decided on the proper size of the handle, screw it into the correct position. It is important to make sure that the new handle is firmly fixed and is turning in the correct direction (clockwise for open and counterclockwise for closed). It is also essential to ensure that it isn't fitted upside down. Replace the screw caps. Once you've completed this step, you should test your handle to make sure that it's working properly. It is also recommended to test the locking mechanism by moving the handle until it is locked position and then back to the locked position. 3. Take off the Screws A uPVC handle is an important part of any house and is the first thing that shows signs of wear or damage. It can be caused by natural causes or from frequent use, and sometimes intentional damage caused by criminals who might wish to open a locked window and gain entry to your home. However, door handles will solve the issue and prevent the issue from recurring. uPVC handles could also be difficult to remove if the locking mechanisms are not working correctly. It is often possible to fix the issue by replacing the multipoint locking mechanism, rather than the whole handle. This could save you money. After you've removed the old handle, you'll need to remove the screws that held it in place. These screws are usually located on the inside of the handle base. You may require an screwdriver to do this, and it's crucial to not over tighten as this can cause the handle to become loose. Then, you'll have to find the screws or pins that keep the handle in place. Again these are likely to be located on the inside face of the base of the handle and you'll need an screwdriver or a pair of pliers in order to remove the screws. If you wish to, you can replace the caps on the screws and check the handle to ensure it works properly. Install the handle by adjusting the spindle to the window's cutout mechanism. Then screw it in. If you wish to replace the screws ensure that the handle is in a slack position and that any screws are securely fixed. Once this is complete you're done and can enjoy your newly replaced window handle. This should help you avoid costly window and door replacements in the near future. If you'd like to get more help in this, or any other aspect of your uPVC windows don't hesitate to get in touch with us. 4. Install the new handle The process of replacing a broken window handle or updating it is easy and can be accomplished in a few easy steps. The key is to identify the type of handle, determine its spindle and identify the tools you'll need to complete the task. Safety is always the primary priority when working with windows and tools. It's also important to be patient and follow the steps carefully to ensure you have a working handle that is safe to use. The first step is to find the screws that hold your current window handle in place and remove these, whilst keeping an appropriate grip on the handle itself to stop it from crashing and injuring yourself. After the screws have been removed they can be repositioned in a safe place to be replaced in the future. After you have removed the handle, you can now begin installing your new handle. It is important that the handle fits perfectly to ensure it works properly and locks the window in place. The next step is to slide the metal square at the back of the handle into the hole in the window mechanism, ensuring that it fits securely. Once the new handle is in place, the last thing to do is replace the screw caps and test it to make sure it functions. If you aren't satisfied with the outcome or if your window doesn't open and close as it should the next step is to call our experts who can help. The majority of UK homes have uPVC Windows. As such, many will require replacement at some point because of damage or wear. The procedure is fairly simple and can be completed by anyone with a bit of experience in DIY. The most important aspect in the success of this procedure is ensuring that you're using a handle that matches the existing window in terms of dimensions and style. Contact our team if you aren't sure of the kind of handle you require. They will be able guide you through all the possibilities.